Craftics #33 Glue Litko Aerosystems
This is the best adhesive you can use for assembling our multi-part acrylic markers. ... Dries clear and will not fog acrylic like thin CA can. ... From the manufacturer's site: ... Craftics Thickened Cement #33, 1.5-oz tube. Fast-setting high-strength, medium-bodied solvent cement. Bonds...
Our
Price:
$3.99
Backorder
Add to Cart
Craftics #33 Thick Acrylic Cement (based on
1
rating)
Litko Aerosystems
Fast-setting high-strength, medium-bodied solvent cement. Bonds acrylics, Rigid PVC, styrene, butyrate, and polycarbonate to themselves and each other, as well as other plastics and porous surfaces. Fills small gaps and dries clear. ... This is the best adhesive you can use for assembling Litko's...
INSTA-CURE Super-Thin Cyanoacrylate Glue Litko Aerosystems
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight-fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor...
1 oz:
Unavailable
½ oz:
Unavailable
INSTA-CURE+ Gap-Filling Cyanoacrylate Glue Litko Aerosystems
INSTA-CURE+ is a higher viscosity CA for loose-fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. INSTA-CURE+ should also be used for large surface areas, including those...
Our
Price:
$4.99
Special Order
Unavailable
INSTA-SET Cyanoacrylate Glue Accelerator 2 oz Litko Aerosystems
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. This spray bottle of INSTA-SET is normally used to cure the CA that flows from joints when parts are pressed together. Applying an...
1 oz:
Unavailable
½ oz:
Unavailable
MAXI-CURE Extra Thick Cyanoacrylate Glue Litko Aerosystems
MAXI-CURE extra-thick CA is the best CA for most plastics, including our Acrylic Flight Bases. MAXI-CURE is the best choice for plastic model assembly. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. ... MAXI-CURE bonds our...
Our
Price:
$6.99
Special Order
Unavailable
MID-CURE 15-Minute Epoxy 4½ oz Litko Aerosystems
MID-CURE 15-min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE in most applications. MID-CURE is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling...
Our
Price:
$6.99
Special Order
Unavailable
QUICK-CURE 5-Minute Epoxy 4½ oz Litko Aerosystems
QUIK-CURE 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal...
SLOW-CURE 30-Minute Epoxy 4½ oz Litko Aerosystems
SLOW-CURE 30-min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE and...
Our
Price:
$2.99
Special Order
Unavailable
UN-CURE Cyanoacrylate Debonder 1 oz Litko Aerosystems
UN-CURE debonder will soften cured CA glue. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and...
